pipe flow expert 8.17 crack
Email : crackrequestnet@gmail.com
New Orifice Component:
- Orifice Component Calculations:
Sharp Edged Orifice
Round Edged Orifice
Bevel Edged Orifice
Thick Edged Orifice
Calculates pressure loss through orifices for liquid systems.
Calculates pressure loss through orifices for gas systems.
Automatically takes account of the gas density at the entry of the orifice.
Calculates for orifices in straight pipes.
Calculates for orifices in transition sections
(where the upstream and downstream pipes are of different size diameters)
Orifice Auto Sizing:
- Orifice Component Sizing:
Auto size orifice diameter to achieve a specified flow rate.
Size orifice diameter to produce a given pressure drop
(for a required flow rate, at a specific Orifice inlet pressure)
Orifice component sizing works for both liquids and gases.
Calculation Engine Enhancements:
- Improved Calculation Engine Algorithm:
Significant improvement in handling complex edge cases in large pipe networks.
Improved identification and selection of critical pipe loops when generating equations.
Enhanced convergence algorithms.
Decimal Places:
- Decimal Places Configuration and Overrides:
By default, numbers are displayed to an appropriate number of decimal places
(based on the given value and unit, and this generally works well in most cases)
New functionality allows the user to override and specify the number of decimal places
for each unit (diameter, length, pressure loss, etc) when values are displayed
– On System Drawing
– On Results Sheet
– On PDF Report
Config Options:
- Config Options Defaults:
Config options can be saved as default values that are automatically loaded on start-up.
New ‘Editor’ tab allows configuration of grid type and other drawing options.
Larger Drawing Area:
- Drawing Area Size Increase:
The total drawing grid size is now 200% of the previous size (twice as large).
Drawing Tool options allow additional configuration of how ‘rubber banding’ starts and stops when drawing pipes.
Isometric Selection Enhancement:
- Isometric Selection Rectangle is now available on Isometric Plane:
Significantly improved selection capabilities when in Isometric mode.
Selection can now also draw a rectangle in the 3D Isometric plane
(which enables better selection of items as they are laid out in the Isometric view).
Drag and Drop Selections to Connect onto Existing Drawing:
- Selection Copy/Paste/Move to Join On to Existing Parts of the Model:
Both 2D selection and 3D Isometric selection now allow the selection to be moved and placed in a new position that ‘joins’ onto an existing part of the system.
Nodes within the selection that overlap existing nodes within the main system are automatically removed.
Pipes within the selection are joined onto the existing nodes
(effectively ‘attaching’ the selection onto part of the existing model).
Move Tool allows Connection to Existing Drawing:
- Move Tool Enhancement:
Moving a node to stretch, shorten, or reposition an existing pipe that is connected to it, now allows the selected node to be placed over a different node within the existing system, to join the pipe on to this part of the model. The selected node is automatically removed and end of the pipe is connected on to the other existing node.
Individual Copy and Paste of Fittings, Components, Control Valves, and Pumps:
- New context sensitive popup submenu
Allows individual items on the current pipe to be copied to their own clipboard.
An individual fitting, component, control valve, or pump can be pasted onto a different pipe.
(either within the same system, or on another system that is open in a separate tab).
Group Updates on Pipes:
- Group Update of Items on a Pipe:
Now supports group copy of control valves and pumps (as well as fittings and components).
A control valve can now be added to the Default Pipe, on the Pipe Data tab in Config Options.
The default control valve can then be copied onto a selected group of pipes.
A pump can now be added to the Default Pipe, on the Pipe Data tab in Config Options.
The default pump can then be copied onto a selected group of pipes.
Group Updates on Nodes:
- Group Update of Node Demands, In-Flows and Out-Flows:
Specify and copy a demand in-flow to a selected group of nodes.
Specify and copy a demand out-flow to a selected group of nodes.
Specify in-flow multipliers and apply to a selected group of nodes.
Specify out-flow multipliers and apply to a selected group of nodes.
Edit Grid, Selections, and Updates:
- Edit Grid Improvements:
Edit Grid now contains additional tabs for Sprinkler K components.
Edit Grid Nodes tab provides capability to multiply In-Flow and Out-Flow demands by a factor.
Edit Grid is now available when a selection is active and filters to show the selected items.
The Edit Grid provides powerful filtering and group update functionality.
Drawing Zoom Scale:
- Zoom Enhancement:
Allow Drawing to Zoom Out down to 10% scale.
Background Images Zoom:
- Zoom Enhancement:
Zoom In and Zoom Out Buttons added for Background Images
Vectorized Background Images:
- Image Imports and Background Images:
Image import now supports Windows Metafile vectorized format.
Allows zoom in and out while maintaining image quality without loss of resolution.
Enhances ability to use background image drawing for tracing over when drawing pipes.
Fully supports image resize, fading, and switch between grayscale and colour.
Results Sheet and PDF Report enhancement for Fittings:
- Additional Fittings Data on Results Sheet and PDF Report:
Individual fitting losses are now shown on the Fittings Tab within the Results Sheet.
Calculation and display of individual Entry and Exit fitting losses within the Fittings Tab.
The above items are also now displayed in the Fittings section of a PDF Report.
PDF System Drawing and Pump Graph Image Scaling:
- Now supports scaling of system image and pump graph image on high-res monitors.
(with Windows scaling factors of 125%, 150%, 200%, 250%, & 300%)
PDF File Size Optimization:
- Results PDF, System Drawing PDF, and Pump Sheet PDF files have been significantly reduced in size
Optimized stored font information.
Ability to select and choose different paper sizes when creating Results PDF documents.
Additional Example Systems:
- An additional 8 new examples systems are included:
New examples demonstrate modeling submerged pumps, ballast systems, and the use of Orifi